Tote Studio
Pick a capacity, a grade, a valve, a lid and a pallet. The drawing redraws, the spec sheet fills in, and the whole configuration travels with your request — written out properly, so the supplier does not have to guess what you meant.
Configure, then request a quote
Your five selections post with the form and go to partner suppliers with your request.
Container enquiries normally arrive as a sentence — “need some 275s, clean, asap” — which takes two or three emails to turn into a quotable spec. Tote Studio collapses that into one submission by making you answer the five questions a supplier would ask anyway: capacity, condition, valve and seat, closure, and base.
The five questions, and why each one matters
- Capacity. Not about volume — about footprint and weight. The standard 275 and 330 gallon composite formats share a 48 × 40 inch footprint, so the decision is really about height and filled weight against your handling ratings. 275 versus 330, in detail.
- Condition and grade. Decided by your liquid and your audit exposure, not by preference. Grade B is right for most industrial chemistry; rebottled is right whenever anyone downstream will ask about provenance.
- Valve and seat. The seat elastomer is the single most commonly mis-specified component in bulk liquid handling. EPDM for water-based chemistry, Viton for aromatics and fats. Compatibility table.
- Closure. Vented for anything pumped or off-gassing; solid for sealed transport. Getting this wrong collapses a bottle inward.
- Base. Steel if it lives outdoors or gets moved often; composite for hygiene and weight; timber indoors only. Pallet types compared.
| Option | Notes |
|---|---|
| Non-standard capacity | Other sizes and stainless formats |
| Tri-clamp fittings | Stainless vessels only |
| Heater jacket | 120 V or 240 V, insulated |
| Insulated cover | Frost and UV protection |
| Spill pallet / bund | 1, 2 or 4 tote |
| Level gauge | Sight tube or float |
| Transfer pump | Diaphragm, drum or 12 V |
| Custom stencilling | To your wording |
Tote Studio FAQ
Does Tote Studio work without JavaScript?
Yes, entirely. The configurator is built from radio buttons; the live drawing and the spec sheet are driven by CSS. Because the controls sit inside the request form, your selections post as part of the normal form submission — no scripts involved at any point.
What happens after I send a configured spec?
Your request goes to partner suppliers with your five selections written out explicitly rather than paraphrased into a message. A supplier follows up with a quote; pricing, freight and availability are set by the supplier.
Can I configure something that is not in the options?
Use the message box. Non-standard capacities, tri-clamp fittings, heater jackets, insulated covers, custom stencilling, secondary containment and upcycled builds can all be requested; availability depends on partner suppliers. The five selections here cover the common path.
Related pages
Tell us what you have.
A partner supplier follows up.
Buying, selling, washing, hauling or recycling: one free, no-obligation request covers all of it. Partner suppliers set the price and availability.
Why the configurator asks what it asks
Each table below is the reasoning behind one of the chip rows above.
Capacity — container formats and dimensions
| Format | Nominal | Usable | L × W × H | Tare (steel base) | Gross, water | Outlet | Lid | Stack filled |
|---|---|---|---|---|---|---|---|---|
| 275 gal standard | 275 gal / 1,041 L | ≈ 265 gal | 48 × 40 × 46" | ≈ 137 lb | ≈ 2,347 lb | 2" S60x6 | 6" screw | Per plate |
| 330 gal standard | 330 gal / 1,249 L | ≈ 320 gal | 48 × 40 × 53" | ≈ 165 lb | ≈ 2,834 lb | 2" S60x6 | 6" screw | Per plate |
| 550 gal | 550 gal / 2,082 L | Varies by maker | Varies; footprint often exceeds 48 × 40" | Varies by maker | Varies by maker | 2" or 3" | 6" screw or similar | Per plate |
| Stainless 275 gal | 275 gal / 1,041 L | Varies by maker | Often near 48 × 40"; height varies | Varies by maker | Varies by maker | 2" or 3" tri-clamp or NPT | Manway | Per plate |
| Stainless 330 gal | 330 gal / 1,249 L | Varies by maker | Often near 48 × 40"; height varies | Varies by maker | Varies by maker | 2" or 3" tri-clamp or NPT | Manway | Per plate |
Condition and grade compared
| Grade A | Grade B | Grade C | Cage / pallet only | |
|---|---|---|---|---|
| Bottle appearance | Clear or near-clear | Some haze or staining | Ghosting or heavy staining | n/a |
| Typical prior contents | Known, benign product | Industrial, declared by the seller | Industrial, declared by the seller | Any; ask what it was |
| Typical cleaning | Washed and rinsed | Washed to suit the residue | Rinsed | Rinsed, if at all |
| Leak check | Ask the supplier | Ask the supplier | Ask the supplier | n/a |
| Valve and gaskets | Usually new | New or sound | Sound or new | n/a |
| Lid | Usually new | New or sound | Sound or new | n/a |
| Marking | Check the plate | Check the plate | May be worn or missing | Check the plate |
| Stacking when filled | Only if the plate and condition allow | Only if the plate and condition allow | Not advised | n/a |
| Food or potable use | Confirm with the supplier and current regulations | Not usually suitable | Not suitable | n/a |
| Common uses | Clean-fill liquids | Industrial liquids | Water, rinse and non-critical duty | Rebottling and fabrication |
Valve and seat — seal compatibility and valve parts
| Medium | EPDM | Viton (FKM) | Silicone | PTFE | Usual first choice |
|---|---|---|---|---|---|
| Water, potable & process | Excellent | Excellent | Excellent | Excellent | EPDM |
| Dilute acids (<10%) | Good | Excellent | Fair | Excellent | EPDM |
| Concentrated acids | Poor | Good | Poor | Excellent | PTFE |
| Caustic soda, alkalis | Excellent | Fair | Fair | Excellent | EPDM |
| Liquid fertilizer, UAN | Excellent | Good | Fair | Excellent | EPDM |
| Glycols, coolants, de-icer | Excellent | Good | Good | Excellent | EPDM |
| Surfactants, detergents | Excellent | Good | Good | Excellent | EPDM |
| Edible oils, fats | Poor | Excellent | Poor | Excellent | Viton |
| Mineral oils | Poor | Excellent | Poor | Excellent | Viton |
| Aromatic solvents | Poor | Excellent | Poor | Excellent | Viton |
| Chlorinated solvents | Poor | Good | Poor | Excellent | Viton / PTFE |
| Ketones (acetone, MEK) | Fair | Poor | Poor | Excellent | PTFE |
| Alcohols | Good | Good | Good | Excellent | EPDM |
| Fuels, diesel, kerosene | Poor | Excellent | Poor | Excellent | Viton |
| Juice & syrup concentrate | Excellent | Excellent | Excellent | Excellent | EPDM |
| Brine, pickling liquor | Good | Excellent | Fair | Excellent | Viton |
| Hot fill 140–180°F | Fair | Excellent | Excellent | Excellent | Viton / silicone |
| Hydrogen peroxide (dilute) | Good | Fair | Fair | Excellent | EPDM / PTFE |
| Sodium hypochlorite | Good | Good | Fair | Excellent | EPDM |
| Steam / CIP chemistry | Excellent | Fair | Good | Excellent | EPDM |
| Outdoor weathering & ozone | Excellent | Good | Excellent | Excellent | EPDM |
| Part | Group | Options | Materials | Typical use |
|---|---|---|---|---|
| 2" butterfly valve | Valves | EPDM, Viton, silicone seat | PP body | Standard composite IBC outlet |
| 3" butterfly valve | Valves | EPDM, Viton seat | PP body | Larger outlets and viscous product |
| 2" ball valve, full bore | Valves | EPDM, Viton seat | PP / PE body | Slurries, pastes, abrasives |
| 3" ball valve | Valves | EPDM, Viton seat | PP body | High-viscosity decanting |
| Stainless ball valve | Valves | 2", 3"; PTFE seat | 304 / 316L | Hot fill, solvents, CIP service |
| Fine-control ball valve | Valves | 2", lever or handwheel | PP | Controlled pail filling |
| Tri-clamp butterfly valve | Valves | 2", 3" | 316L, EPDM / PTFE | Sanitary stainless vessels |
| Gate valve | Valves | 2", 3" | Cast iron, PTFE seat | Legacy steel vessels only |
Closure — lids, caps and when to vent
| Part | Group | Options | Materials | Typical use |
|---|---|---|---|---|
| 6" screw lid, vented | Closures | One-way, two-way vent | HDPE | Pumped discharge, off-gassing, outdoor |
| 6" screw lid, solid | Closures | n/a | HDPE | Sealed transport and storage |
| Tamper-evident dust cap | Closures | Plain, numbered | PE | Transit protection and evidence |
| Camlock dust plug / cap | Closures | DC, DP | PP, aluminum | Closing an unused half |
Pallet base compared
| Factor | Steel | Composite | Timber |
|---|---|---|---|
| Outdoor life | Long while the zinc holds | Good, UV-dependent | Poor; rots when left wet |
| Forklift tolerance | Excellent | Fair; decks can crack | Fair; bearers can split |
| Pallet-jack entry | Often four-way | Often four-way, check depth | Often two-way only |
| Repairable | Often, by a repair shop | No | Partly |
| Washability | Good | Excellent | Poor |
| Pest and splinter risk | None | None | Real |
| Rot and delamination | None | None | Common |
| ISPM 15 on export | Not applicable | Not applicable | Generally required for solid wood |
| Hygiene-sensitive use | Acceptable | Preferred | Avoid |
| Relative cost new | Usually highest | Usually middle | Usually lowest |
Weight check — before you fix the capacity
| Product | Typical SG | 275 gal filled | 330 gal filled |
|---|---|---|---|
| Acetone | 0.79 | 1,883 lb | 2,273 lb |
| Ethanol | 0.79 | 1,883 lb | 2,273 lb |
| Kerosene | 0.81 | 1,927 lb | 2,327 lb |
| Diesel fuel | 0.85 | 2,016 lb | 2,433 lb |
| Mineral oil | 0.88 | 2,082 lb | 2,514 lb |
| Biodiesel B100 | 0.88 | 2,082 lb | 2,514 lb |
| Canola oil | 0.91 | 2,148 lb | 2,594 lb |
| Soybean or olive oil | 0.92 | 2,170 lb | 2,620 lb |
| Water | 1.00 | 2,347 lb | 2,834 lb |
| Vinegar | 1.01 | 2,369 lb | 2,860 lb |
| Milk | 1.03 | 2,413 lb | 2,914 lb |
| Propylene glycol | 1.04 | 2,436 lb | 2,941 lb |
| Apple cider | 1.05 | 2,458 lb | 2,967 lb |
| Urea solution (DEF) | 1.09 | 2,546 lb | 3,074 lb |
| Ethylene glycol | 1.11 | 2,590 lb | 3,127 lb |
| Hydrogen peroxide 35% | 1.13 | 2,634 lb | 3,181 lb |
| Hydrochloric acid 31% | 1.16 | 2,701 lb | 3,261 lb |
| Salt brine 23% | 1.17 | 2,723 lb | 3,287 lb |
| Sodium hypochlorite 12% | 1.21 | 2,811 lb | 3,394 lb |
| Glycerine | 1.26 | 2,922 lb | 3,528 lb |
| Sulfuric acid 35% | 1.26 | 2,922 lb | 3,528 lb |
| Sodium hydroxide 25% | 1.27 | 2,944 lb | 3,554 lb |
| UAN 28 | 1.28 | 2,966 lb | 3,581 lb |
| Calcium chloride 30% | 1.28 | 2,966 lb | 3,581 lb |
| Latex paint | 1.30 | 3,010 lb | 3,634 lb |
| UAN 32 fertilizer | 1.32 | 3,054 lb | 3,688 lb |
| Liquid sugar or maple syrup | 1.33 | 3,076 lb | 3,715 lb |
| Juice concentrate (70 Brix) | 1.35 | 3,121 lb | 3,768 lb |
| High-fructose corn syrup | 1.38 | 3,187 lb | 3,848 lb |
| Liquid starter 10-34-0 | 1.38 | 3,187 lb | 3,848 lb |
| Molasses or honey | 1.42 | 3,275 lb | 3,955 lb |
| Ferric chloride 40% | 1.42 | 3,275 lb | 3,955 lb |
| Potassium hydroxide 45% | 1.46 | 3,364 lb | 4,061 lb |
| Sodium hydroxide 50% | 1.52 | 3,496 lb | 4,222 lb |
| Phosphoric acid 75% | 1.58 | 3,629 lb | 4,382 lb |
| Sulfuric acid 93% | 1.83 | 4,181 lb | 5,049 lb |
| Configuration | Load per beam level | Rating needed |
|---|---|---|
| One 275 gal, water | 2,347 lb | 3,000 lb level |
| One 275 gal, SG 1.3 | 3,010 lb | 3,500 lb level |
| Two 275 gal, water | 4,694 lb | 5,000 lb level |
| Two 275 gal, SG 1.3 | 6,020 lb | 6,500 lb level |
| Two 275 gal, SG 1.5 | 6,904 lb | 7,500 lb level |
| One 330 gal, water | 2,834 lb | 3,000 lb level |
| One 330 gal, SG 1.3 | 3,634 lb | 4,000 lb level |
| Two 330 gal, water | 5,668 lb | 6,000 lb level |
| Two 330 gal, SG 1.3 | 7,268 lb | 7,500 lb level |
Everything else that is quotable
The configurator covers the common path. These are the parts and accessories you can ask partner suppliers about.
| Part | Group | Options | Materials | Typical use |
|---|---|---|---|---|
| 2" butterfly valve | Valves | EPDM, Viton, silicone seat | PP body | Standard composite IBC outlet |
| 3" butterfly valve | Valves | EPDM, Viton seat | PP body | Larger outlets and viscous product |
| 2" ball valve, full bore | Valves | EPDM, Viton seat | PP / PE body | Slurries, pastes, abrasives |
| 3" ball valve | Valves | EPDM, Viton seat | PP body | High-viscosity decanting |
| Stainless ball valve | Valves | 2", 3"; PTFE seat | 304 / 316L | Hot fill, solvents, CIP service |
| Fine-control ball valve | Valves | 2", lever or handwheel | PP | Controlled pail filling |
| Tri-clamp butterfly valve | Valves | 2", 3" | 316L, EPDM / PTFE | Sanitary stainless vessels |
| Gate valve | Valves | 2", 3" | Cast iron, PTFE seat | Legacy steel vessels only |
| S60x6 to 3/4" GHT | Adapters | Male / female | PP, nylon, brass | Garden hose connection |
| S60x6 to 2" NPT | Adapters | Male / female | PP, nylon | Pipe and pump connection |
| S60x6 to camlock | Adapters | Type A, F; 2" | PP, aluminum, 316 | Quick-connect transfer |
| S56x4 to S60x6 converter | Adapters | n/a | PP | Older and imported bottles |
| Camlock coupler | Adapters | Types A–F, DC, DP | PP, aluminum, 316 | Hose and pump halves |
| Hose tail / shank | Adapters | 3/4" to 3" | PP, brass, stainless | Hose clamping |
| Reducer / increaser | Adapters | 2"×3", 2"×1.5" | PP, aluminum | Matching an existing hose |
| 2.5" fire thread adapter | Adapters | NST / NH | Aluminum, brass | Fire-water draft points |
| Bulkhead fitting | Adapters | 1/2" to 2" | PP, EPDM gaskets | Through-wall on upcycled builds |
| 6" screw lid, vented | Closures | One-way, two-way vent | HDPE | Pumped discharge, off-gassing, outdoor |
| 6" screw lid, solid | Closures | n/a | HDPE | Sealed transport and storage |
| Tamper-evident dust cap | Closures | Plain, numbered | PE | Transit protection and evidence |
| Camlock dust plug / cap | Closures | DC, DP | PP, aluminum | Closing an unused half |
| Outlet gasket, flat | Seals | EPDM, Viton, silicone | Rubber compound to suit the liquid | The usual cause of a leak |
| Outlet gasket, O-ring | Seals | EPDM, Viton | Rubber compound to suit the liquid | Some valve patterns |
| PTFE envelope gasket | Seals | EPDM or silicone core | PTFE | Aggressive or mixed chemistry |
| Lid seal | Seals | Foam, EPDM, silicone | Rubber compound to suit the liquid | Second most degraded part |
| Cage, 275 gal | Structure | New or reused | Galvanized steel tube | Rebottling, racking, fabrication |
| Cage, 330 gal | Structure | New or reused | Galvanized steel tube | As above |
| Cage section | Structure | Panel, upright, foot | Galvanized steel | Repair |
| Steel pallet | Structure | New or repaired | Galvanized steel | The usual base on composite totes |
| Composite pallet | Structure | Reused or new | Molded plastic | Hygiene-sensitive environments |
| Timber pallet | Structure | New or reused | Softwood | Indoor, dry, cost-led |
| Spill pallet / bund | Handling | 1, 2 or 4 tote | PE | Secondary containment |
| Tote stand | Handling | Fixed, adjustable | Galvanized steel | Gravity head for decanting |
| Tote tipper frame | Handling | Manual | Steel | Draining the last heel |
| Transfer pump | Handling | Diaphragm, drum, 12 V | PP / SS wetted parts | Dispensing |
| Heater jacket | Temperature | 120 V, 240 V | Insulated heating element | Winter viscosity, freeze protection |
| Insulated cover | Temperature | 275 / 330 gal | Reflective PE / PVC | Frost and UV protection |
| UV / blackout cover | Temperature | 275 / 330 gal | UV-stable PE | Algae control, slows UV aging |
| Level gauge | Measurement | Sight tube, float | PE / PP | Inventory |
| Temperature strip | Measurement | Adhesive | n/a | Freeze and hot-fill monitoring |
| Stencil kit | Measurement | Custom wording | n/a | Fleet marking |
The reference tables, each published in full
Every reference table on this site and the page it lives on. None of it is behind a form.