IBC Totes RecoPartner-supplied totesRequest a quote
Buying guide · November 4, 2024

It may be the gasket, not the tote: how to diagnose a leak

A tote that seems ready to be scrapped often just has a tired seal. A simple check tells you which problem you have.

Quote request

Question about this piece?

Put it in the message box. A partner supplier follows up on tote requests.

Business or personal — disposable addresses are rejected
US or Canada only, 10 digits including area code
Two letters — must match the postal code
US ZIP or Canadian postal code
Whole units, 1 – 1,000,000

Required fields are marked *. The request is free and carries no obligation. Your details go to our lead platform and partner suppliers so they can prepare a quote.

Short answer

Many tote leaks come from a replaceable part: the outlet gasket, the valve, or the lid seal. Check those first. Drain and dry the tote, add a little water on a dry floor, wait, and see where the water appears. Wet at the valve points to a gasket or valve. Wet on the wall or at a lower corner points to the bottle, and that is a much more serious problem.

The four usual suspects

Where a leak usually comes from
SourceTypical signTypical fix
Outlet gasketWeeping where the valve meets the bossReplace the gasket
Valve seatDrip from the valve outlet when closedReplace the valve
Lid sealWet at the lid when the tote is moved or tippedReplace the seal
BottleDamp wall, split seam, wet lower cornerRebottle, recycle or retire

Why gaskets fail

Compression set. A gasket under constant load slowly loses its ability to spring back. It still looks like a gasket but no longer seals like one. This is normal aging, so treat seals as consumables.

Chemical attack. A common case is EPDM exposed to oils, fuels or solvents. It swells, softens and stops sealing. The material was the wrong choice, so replacing like for like only restarts the clock. Check the gasket compatibility guide.

Reuse. Someone removes the valve to clean the tote and puts the old gasket back. A used gasket has already taken its set and may not seal again. Fit a new one whenever the valve comes off.

How to find the leak

  1. Drain and clean the tote following the product SDS, then wipe the valve boss, lid seat and lower seam dry. You cannot read a leak through a film of product.
  2. Add a few inches of water with the tote on a dry floor, then wait a while. A wet spot at the valve points to a gasket or seat. A damp patch on the wall points to the bottle.
  3. Fill higher if nothing shows, since some leaks appear only under more pressure. Do this where a leak will do no harm, and do not pressurize the tote.
  4. Inspect the gasket. Hard and shiny suggests age. Swollen and soft suggests chemical attack. Permanently flattened suggests compression set. Cracked at the inner edge can mean the valve was cross-threaded.
  5. Check the sealing face. A new gasket that still weeps points to the boss or valve flange: scoring, warping or distortion.

If a new gasket, a new valve and a clean boss do not stop it, the bottle is probably the problem. Then the choice is rebottling or recycling. How to recognize a failed bottle.

If the leak involves a hazardous product, stop and follow the SDS and your site's spill procedures first. Never try to fix a leak on a tote that is still under load from a hazardous product.

If you run a lot of totes

Keep spare seals on hand. It is one of the simplest ways to get more life from your containers.

  • Outlet gaskets in the material your product needs, which may not be the one that came with the tote.
  • Lid seals, which are easy to overlook.
  • A couple of spare valves, so a worn seat is a short job instead of a long wait.
  • Tamper-evident caps, which show at a glance whether a valve has been opened.
  • A strap wrench. A pipe wrench can distort the valve body and cause the next leak.

Why it is worth the effort

Scrapping a sound tote because of a seal wastes a working container. Replacing the seal keeps that tote in service and avoids buying a new one. More on reuse.

Need replacement parts? Browse the accessories, then request a quote. Parts are available through partner suppliers.


Published November 4, 2024.

gasketsmaintenanceleaksparts
Reference

Reference tables

General product facts for planning, each on its own page.

Grades: what the labels usually mean
Grades A, B and C against cage-only: what each usually means. Grades are not a standard, so confirm the definition with the supplier
Grade AGrade BGrade CCage / pallet only
Bottle appearanceClear or near-clearSome haze or stainingGhosting or heavy stainingn/a
Typical prior contentsKnown, benign productIndustrial, declared by the sellerIndustrial, declared by the sellerAny; ask what it was
Typical cleaningWashed and rinsedWashed to suit the residueRinsedRinsed, if at all
Leak checkAsk the supplierAsk the supplierAsk the suppliern/a
Valve and gasketsUsually newNew or soundSound or newn/a
LidUsually newNew or soundSound or newn/a
MarkingCheck the plateCheck the plateMay be worn or missingCheck the plate
Stacking when filledOnly if the plate and condition allowOnly if the plate and condition allowNot advisedn/a
Food or potable useConfirm with the supplier and current regulationsNot usually suitableNot suitablen/a
Common usesClean-fill liquidsIndustrial liquidsWater, rinse and non-critical dutyRebottling and fabrication
Unit conversions
Unit conversions used across this site
QuantityFromEquals
Volume1 US gallon3.785 liters
Volume1 liter0.2642 US gallons
Volume275 US gal1,041 liters
Volume330 US gal1,249 liters
Volume1 cubic foot7.481 US gallons
Volume1 US gal0.1337 cubic feet
Weight1 US gal of water8.34 lb
Weight1 liter of water1.0 kg
Weight1 lb0.4536 kg
Weight1 kg2.2046 lb
Weight1 short ton2,000 lb / 907 kg
Length1 inch25.4 mm
Length48"1,219 mm
Length40"1,016 mm
Pressure1 psi6.895 kPa
Pressure1 bar14.5 psi
Pressure1 foot of water head0.433 psi
Temperature140°F60°C
Temperature180°F82°C
Area1 sq ft0.0929 m²
Rainfall yield1" rain on 1,000 sq ft≈ 620 gallons before losses
IBC Totes Reco