IBC Totes RecoPartner-supplied totesRequest a quote
Projects · October 7, 2024

Building a 1,060-gallon four-tote rain array

One tote fills and overflows in a moderate storm. Four, connected low, behave like a single tank, and the plumbing is easier than people expect.

Quote request

Question about this piece?

Put it in the message box. A partner supplier follows up on tote requests.

Business or personal — disposable addresses are rejected
US or Canada only, 10 digits including area code
Two letters — must match the postal code
US ZIP or Canadian postal code
Whole units, 1 – 1,000,000

Required fields are marked *. The request is free and carries no obligation. Your details go to our lead platform and partner suppliers so they can prepare a quote.

Short answer

Four 275-gallon totes on one level pad, connected low with 2-inch fittings and flexible hose, behave like a single tank of about 1,060 usable gallons that equalizes by gravity. Filled, the array weighs about 9,400 lb, or roughly 175 lb per square foot if the totes stand tight together, so the pad is the real engineering. Pipe the overflow well away from buildings, block all light, and drain the array or leave room for ice before winter.

Why four totes

An inch of rain on 1,000 square feet of roof is about 620 gallons before losses. A single 275-gallon tote fills well before the storm is over, and the rest of the water goes to waste.

Four totes hold about 1,060 usable gallons, which covers around an inch and three quarters of rain on that roof. Beyond that, an extra tote only pays off on a larger roof or where you use water quickly enough to empty the tanks between storms.

Four is also easy to lay out. Two by two makes a compact pad with short connections. Longer rows need longer hoses and are more exposed to uneven settling.

Before you start, check local rules on rainwater collection and tank placement. Harvested rainwater is not drinking water. Choose totes that held harmless contents, and ask the supplier what they held.

Step 1: build the pad

The pad is the part that decides whether the array lasts. Four full totes weigh about 9,400 lb on about 53 square feet. Lawn and bare soil will not carry that evenly, and patio slabs on sand tend to settle and rack the cages.

  • Compacted gravel over geotextile, graded level in both directions, is usually the simplest choice that works. Depth depends on your ground.
  • Concrete pavers on a compacted base work if they run continuously under each pallet, not just at the corners.
  • A concrete slab is the long-term answer if you plan to keep the array in place.
  • A raised deck or platform needs to be designed for the load. If the array will be raised, or near a slope or a building, ask a qualified professional.

Level matters for structural reasons. Since the array equalizes by gravity, tilt puts extra depth on the low tote and uneven loads on the cages. Check with a long level in both directions.

Step 2: connect the totes low

What makes four totes act as one is connecting them low. Water finds its own level, so a low connection means all four fill and empty together, and you can draw from any of them.

  1. Fit a 2-inch gasketed bulkhead fitting low on the wall of each bottle, as close to the base as the cage allows. Self-tapping or threaded-into-the-wall fixes are not reliable under water pressure.
  2. Connect adjacent pairs with short lengths of 2-inch flexible hose and camlocks. Use flexible hose because the totes move a little as they fill and empty, and rigid pipe passes that movement into the fitting.
  3. Join the two pairs with a third hose to make a simple H-shaped manifold.
  4. Keep the original outlets in place on all four totes. Use one to draw water and the others as drains.
  5. Add an isolating valve to each connection if you can, so one tote can be taken out without draining the whole array.

Keep every connection reachable. You will come back to the manifold to winterize, isolate a tote or clear sediment.

Step 3: inlet, first flush and overflow

Feed the array into one tote. One inlet with one first-flush diverter and one screened opening is simpler to build and clear than four of each, and the manifold shares the water anyway.

A common rule of thumb is to divert one to two gallons per 100 square feet of roof, so ten to twenty gallons on 1,000 square feet. The diverter is a vertical pipe that fills first and drains slowly, taking the dust, pollen and droppings from the first rain away from your storage.

Then fit the overflow. Put a 2-inch outlet high on the last tote and pipe it to a safe discharge point, away from foundations and neighboring property. The array will overflow in heavy rain, so plan where that water goes.

Step 4: block the light

Natural HDPE lets light through. Stored water in sunlight grows algae, and ultraviolet light is what breaks down the bottle. Paint the outside with a dark exterior coating that suits HDPE, wrap the array in a UV-stable cover, or build it under a lean-to.

This solves both problems at once: less algae and a longer-lived bottle. The failure you are avoiding.

Step 5: winterize

If you get hard frosts, plan for them. Low-level hoses hold water and freeze long before the tanks do.

  • Drain the manifold completely, or remove the hoses and store them.
  • Empty the totes, or leave each no more than about two thirds full with a vented lid so that ice has room to expand.
  • Remove or insulate the draw-off valve and any hose.
  • Close the inlet or divert the downspout so a thaw does not refill the array before the next freeze.
  • Leave isolating valves open so that water is not trapped between closed valves.

What you will need

Typical parts for a four-tote array, excluding the pad
ItemQtyNote
275-gallon totes4Confirm prior contents with the supplier
2-inch bulkhead fittings4Gasketed on both sides
2-inch flexible hoses and camlocks3Short and easy to reach
Isolating valves3Optional but useful
First-flush diverter1Sized to your roof
Screened inlet adapter1Keeps out debris and insects
2-inch overflow pipe and elbows1 runTo a safe discharge point
Vented lids4For winter and for drawing down
Exterior coating or UV cover1Do not skip this
Draw-off valve and hose adapter1Check your tote's outlet thread first

Grade C totes are often a good fit here because a rain tank does not need a perfect bottle, though the cage and wall still have to be sound. Valves and fittings are worth checking against your tote before you order.

Three common mistakes

  1. Connecting high instead of low. A high connection only lets one tote spill into the next. Connect low and the array shares its level.
  2. Rigid plumbing into bulkheads. Totes move as they fill, and rigid pipe passes that into the fitting and the wall.
  3. Using a tote with unsuitable prior contents. A tote that held chemicals, fertilizer or crop protection products can hold traces however well it is washed. Do not use one to water anything you will eat unless you have confirmed it is suitable.

Planning a build? Tell us the size of your roof and how you will use the water. We pass your request to a partner supplier for totes and fittings. Request a quote. More ideas are on the upcycled page and in the rainwater guide.


Published October 7, 2024.

rainwaterprojectsupcyclingbuild guide
Reference

Reference tables

General product facts for planning, each on its own page.

Grades: what the labels usually mean
Grades A, B and C against cage-only: what each usually means. Grades are not a standard, so confirm the definition with the supplier
Grade AGrade BGrade CCage / pallet only
Bottle appearanceClear or near-clearSome haze or stainingGhosting or heavy stainingn/a
Typical prior contentsKnown, benign productIndustrial, declared by the sellerIndustrial, declared by the sellerAny; ask what it was
Typical cleaningWashed and rinsedWashed to suit the residueRinsedRinsed, if at all
Leak checkAsk the supplierAsk the supplierAsk the suppliern/a
Valve and gasketsUsually newNew or soundSound or newn/a
LidUsually newNew or soundSound or newn/a
MarkingCheck the plateCheck the plateMay be worn or missingCheck the plate
Stacking when filledOnly if the plate and condition allowOnly if the plate and condition allowNot advisedn/a
Food or potable useConfirm with the supplier and current regulationsNot usually suitableNot suitablen/a
Common usesClean-fill liquidsIndustrial liquidsWater, rinse and non-critical dutyRebottling and fabrication
Unit conversions
Unit conversions used across this site
QuantityFromEquals
Volume1 US gallon3.785 liters
Volume1 liter0.2642 US gallons
Volume275 US gal1,041 liters
Volume330 US gal1,249 liters
Volume1 cubic foot7.481 US gallons
Volume1 US gal0.1337 cubic feet
Weight1 US gal of water8.34 lb
Weight1 liter of water1.0 kg
Weight1 lb0.4536 kg
Weight1 kg2.2046 lb
Weight1 short ton2,000 lb / 907 kg
Length1 inch25.4 mm
Length48"1,219 mm
Length40"1,016 mm
Pressure1 psi6.895 kPa
Pressure1 bar14.5 psi
Pressure1 foot of water head0.433 psi
Temperature140°F60°C
Temperature180°F82°C
Area1 sq ft0.0929 m²
Rainfall yield1" rain on 1,000 sq ft≈ 620 gallons before losses
IBC Totes Reco