IBC Totes RecoPartner-supplied totesRequest a quote
Compliance · July 15, 2024

Reading a UN plate in the field

Reading the plate on a tote takes a couple of minutes. It tells you how the container was designed and tested, though not everything you need to know.

Quote request

Question about this piece?

Put it in the message box. A partner supplier follows up on tote requests.

Business or personal — disposable addresses are rejected
US or Canada only, 10 digits including area code
Two letters — must match the postal code
US ZIP or Canadian postal code
Whole units, 1 – 1,000,000

Required fields are marked *. The request is free and carries no obligation. Your details go to our lead platform and partner suppliers so they can prepare a quote.

Short answer

Find the plate and check that every character is legible. Then read the category digits (31 means liquids), the material letters (HA means a plastic inner in a steel outer), the packing group letter (X, Y or Z), the date of manufacture, and any reconditioner mark. The plate tells you what the design was tested for. Whether a particular tote can be used for a regulated material today depends on current regulations and on its records.

Who needs to read it

If you are buying a tote for water, site storage or a project, the plate matters little, and an unmarked tote may suit you fine.

If you plan to ship a regulated liquid, the marking is central to the decision, and that decision belongs to the shipper. A general guide like this one is not compliance advice. Use it to understand what you are reading, then check current regulations and qualified advice for your material.

Step 1: find it, and judge legibility first

On a composite tote the marking is usually on a metal or plastic plate attached to the cage, often on the valve side. Some information may also be molded into the bottle.

Before reading anything, decide whether you can read every character. If you have to guess at the date or code, the plate cannot support a decision. Treat that tote as unmarked.

Step 2: the category digits

The first two digits of the code tell you what the packaging was designed for.

Common category digits
DigitsDesigned forTypical code
31Liquids31HA1
21Solids, discharged under pressure21HA1
11Solids, discharged by gravity11HA1

This is the quickest check there is. A solids-rated tote can look just like the one beside it and still not be rated for a regulated liquid, so look for this in mixed lots.

Step 3: the material letters

The letters describe how the tote is built. H stands for plastic and A for steel. HA is a plastic inner receptacle in a steel outer frame, which is the standard caged composite tote. Stainless IBCs carry a different code, with no H. The digit after the letters identifies the construction variant.

Step 4: the packing group letter

This letter is easy to overlook and it matters. It shows which packing groups the design was tested for.

  • X: packing groups I, II and III.
  • Y: packing groups II and III. Common on composite totes.
  • Z: packing group III only.

Step 5: date, country and maker

The date is usually written as month and year, so 0324 would be March 2024. Nearby you will find a code for the country that approved the design and a code for the manufacturer.

The date also gives you the bottle's age. Combined with a thumb press on the wall, that says more about its remaining life than appearance does. What a tired bottle looks like.

Step 6: the reconditioner mark

A reconditioned tote may carry an added mark showing who did the work and when. If a tote has clearly been reconditioned and shows no such mark, ask who cleaned it and what records exist.

Step 7: the load figures

The marking also gives maximum gross mass and a stacking test load. Note these down. Dense liquids can reach the mass limit well before the tote is full, so run the numbers on your product's specific gravity.

What the plate does not tell you

The plate shows what the design was built and tested as. It does not show what this tote held, how it has been treated, or whether it is currently in date for regulated use. Periodic inspection and testing requirements can apply, so check current regulations and ask the supplier for records before you agree to buy.

The field cheat sheet

  1. Every character legible? If not, treat as unmarked.
  2. Starts with 31? If not and you are shipping liquid, stop.
  3. Does the packing group letter cover your material?
  4. Note the date, and feel the bottle wall while you are there.
  5. Reconditioner mark present? Note the code and date.
  6. Write down maximum gross mass and stacking load.
  7. Ask for inspection and test records, and check current regulations.

For the element-by-element reference, see the UN marking guide. Need totes? Request a quote and a partner supplier can follow up. Suitability for regulated goods must be confirmed with the supplier and current regulations.


Published July 15, 2024.

UN markingcomplianceinspection
Reference

Reference tables

General product facts for planning, each on its own page.

Grades: what the labels usually mean
Grades A, B and C against cage-only: what each usually means. Grades are not a standard, so confirm the definition with the supplier
Grade AGrade BGrade CCage / pallet only
Bottle appearanceClear or near-clearSome haze or stainingGhosting or heavy stainingn/a
Typical prior contentsKnown, benign productIndustrial, declared by the sellerIndustrial, declared by the sellerAny; ask what it was
Typical cleaningWashed and rinsedWashed to suit the residueRinsedRinsed, if at all
Leak checkAsk the supplierAsk the supplierAsk the suppliern/a
Valve and gasketsUsually newNew or soundSound or newn/a
LidUsually newNew or soundSound or newn/a
MarkingCheck the plateCheck the plateMay be worn or missingCheck the plate
Stacking when filledOnly if the plate and condition allowOnly if the plate and condition allowNot advisedn/a
Food or potable useConfirm with the supplier and current regulationsNot usually suitableNot suitablen/a
Common usesClean-fill liquidsIndustrial liquidsWater, rinse and non-critical dutyRebottling and fabrication
Unit conversions
Unit conversions used across this site
QuantityFromEquals
Volume1 US gallon3.785 liters
Volume1 liter0.2642 US gallons
Volume275 US gal1,041 liters
Volume330 US gal1,249 liters
Volume1 cubic foot7.481 US gallons
Volume1 US gal0.1337 cubic feet
Weight1 US gal of water8.34 lb
Weight1 liter of water1.0 kg
Weight1 lb0.4536 kg
Weight1 kg2.2046 lb
Weight1 short ton2,000 lb / 907 kg
Length1 inch25.4 mm
Length48"1,219 mm
Length40"1,016 mm
Pressure1 psi6.895 kPa
Pressure1 bar14.5 psi
Pressure1 foot of water head0.433 psi
Temperature140°F60°C
Temperature180°F82°C
Area1 sq ft0.0929 m²
Rainfall yield1" rain on 1,000 sq ft≈ 620 gallons before losses
IBC Totes Reco