IBC Totes RecoPartner-supplied totesRequest a quote
Process · December 8, 2025

The water a tote wash needs, and where it goes

Recirculation is the difference between washing containers and running up a water bill. Here is how a typical treatment train works, stage by stage.

Quote request

Question about this piece?

Put it in the message box. A partner supplier follows up on tote requests.

Business or personal — disposable addresses are rejected
US or Canada only, 10 digits including area code
Two letters — must match the postal code
US ZIP or Canadian postal code
Whole units, 1 – 1,000,000

Required fields are marked *. The request is free and carries no obligation. Your details go to our lead platform and partner suppliers so they can prepare a quote.

Short answer

Washing a tote properly moves a lot of water. Larger reconditioners commonly recirculate much of it through a train of settling, dissolved-air flotation and filtration, then top up with fresh water. The real limit is the sludge that treatment concentrates, which has to be characterised and disposed of properly. If you wash in-house, plan where the water goes before you turn it on.

Why recirculation matters

A full wash cycle with fresh water every time uses a large volume per container. At any real throughput that becomes a big water bill and a big effluent problem, and it limits how much washing a site can physically do.

A closed-loop treatment train cuts fresh water use, cuts effluent volume, and removes water supply and discharge as the limit on throughput. That is why it is common at larger wash operations.

A typical train, stage by stage

Stage 0: pre-drain and segregation

Before any water is involved, the residual heel is drained to separate tanks by type of prior product, for example water-based, oil-based and anything held back for checking.

This is arguably the most important stage and it needs no equipment at all. Mixing incompatible heels can generate heat or gas, and an unidentified heel in the wrong tank can shut a line down. The classification depends on an accurate prior-contents declaration. Why traceable paperwork matters.

Stage 1: coarse settling

Gravity does the cheap work. Baffled chambers give the water time to drop out solids, fibre and the heavier fraction.

Nothing clever happens here, and it often removes more material than any other stage. The baffles matter more than the volume: water short-circuiting across the top of a chamber is a common design fault in small effluent plants.

Stage 2: dissolved-air flotation

Fine bubbles introduced at the base lift suspended particles and residual oils to a surface layer that is skimmed off. Dissolved-air flotation (DAF) is what takes water from settled to reusable for washing.

It is sensitive to temperature, so it tends to work less well in cold weather.

Stage 3: filtration, pH correction, re-dosing

The water is filtered, its pH corrected, and the cleaning chemistry topped back up to working strength before it returns to the wash.

Re-dosing takes discipline. Caustic is used up by the residue it attacks, so a loop drifts weaker over a shift. Well-run lines measure the concentration rather than assuming it, because a cycle at half strength is wasted time and a container that needs washing again. What caustic does and does not do.

Stage 4: heat recovery

A heat exchanger can take heat from outgoing rinse water and pass it to incoming water, so the heater does less work, especially in winter. Strictly this saves energy rather than water, but it sits in the same pipework.

The part nobody talks about: sludge

Every stage above concentrates something. Settled solids, flotation skimmings and spent filter media all become sludge, and sludge is the honest limit on how clean any wash operation can claim to be.

It has to be dewatered, characterised by what the containers held, and sent to an appropriate facility. A reconditioner that claims everything is reused or recycled is either not counting this stream or not mentioning it. It is a fair question to ask any supplier.

If you are considering washing in-house

The chemistry is the easy part. The water is the hard part.

  • Plan the effluent before you turn the water on. This is the step everyone skips and the one that creates legal problems. Wash water carries whatever you just removed, and how you may dispose of it depends on what that is. Check current regulations and your local authority's rules.
  • Never put it down a storm drain. Some dilute, benign wash water may be acceptable to a sanitary sewer with your authority's permission; fertilisers, crop protection products, pigments and solvents generally are not.
  • Capture the first rinse separately. It is the most contaminated and the smallest in volume, so treating it as its own stream is the cheapest improvement you can make.
  • Keep heels out of the rinse water. A drum for the heel costs little and makes everything downstream easier.
  • If it needs caustic, send it out. At that point the recorded process, the water loop and the disposal route are what you are really paying for. Reconditioning through partner suppliers.

A practical method for washing water-miscible and oily residues safely, without a caustic circuit, is on how to clean an IBC tote.


Published December 8, 2025.

waterDAFeffluentprocess
Reference

Reference tables

General product facts for planning, each on its own page.

Grades: what the labels usually mean
Grades A, B and C against cage-only: what each usually means. Grades are not a standard, so confirm the definition with the supplier
Grade AGrade BGrade CCage / pallet only
Bottle appearanceClear or near-clearSome haze or stainingGhosting or heavy stainingn/a
Typical prior contentsKnown, benign productIndustrial, declared by the sellerIndustrial, declared by the sellerAny; ask what it was
Typical cleaningWashed and rinsedWashed to suit the residueRinsedRinsed, if at all
Leak checkAsk the supplierAsk the supplierAsk the suppliern/a
Valve and gasketsUsually newNew or soundSound or newn/a
LidUsually newNew or soundSound or newn/a
MarkingCheck the plateCheck the plateMay be worn or missingCheck the plate
Stacking when filledOnly if the plate and condition allowOnly if the plate and condition allowNot advisedn/a
Food or potable useConfirm with the supplier and current regulationsNot usually suitableNot suitablen/a
Common usesClean-fill liquidsIndustrial liquidsWater, rinse and non-critical dutyRebottling and fabrication
Unit conversions
Unit conversions used across this site
QuantityFromEquals
Volume1 US gallon3.785 liters
Volume1 liter0.2642 US gallons
Volume275 US gal1,041 liters
Volume330 US gal1,249 liters
Volume1 cubic foot7.481 US gallons
Volume1 US gal0.1337 cubic feet
Weight1 US gal of water8.34 lb
Weight1 liter of water1.0 kg
Weight1 lb0.4536 kg
Weight1 kg2.2046 lb
Weight1 short ton2,000 lb / 907 kg
Length1 inch25.4 mm
Length48"1,219 mm
Length40"1,016 mm
Pressure1 psi6.895 kPa
Pressure1 bar14.5 psi
Pressure1 foot of water head0.433 psi
Temperature140°F60°C
Temperature180°F82°C
Area1 sq ft0.0929 m²
Rainfall yield1" rain on 1,000 sq ft≈ 620 gallons before losses
IBC Totes Reco